Setek WiFi Extender Reset Guide (Quick & Easy Steps)

Resetting is a simple process that can solve many problems like big bugs and glitches. Every device has this process inbuilt even in your phone. Reset your device is like deleting all the files, store data & manage settings from the device. This process makes it a new one like it was at the time of first Setek WiFi extender setup.

Here we discuss why reset Setek WiFi extender, how to do it and other troubleshooting tips than setting the device.

Why Reset Setek WiFi Extender?

Resetting isn’t some magic “make it faster” button. It’s more like hitting “refresh” on a stubborn app that won’t load. It wipes all the junk settings, the old SSIDs, passwords, maybe even weird internal glitches that creep in when the device runs nonstop. After a reset, it’s basically a blank slate. You set it up again like it just came out of the box, and most of the time, issues gone.

How to Reset Setek WiFi Extender?

Locate the Extender
First thing, find your Setek WiFi extender. Usually plugs into a wall somewhere mid-house. Make sure it’s powered on — the lights should be blinking or solid.

Find the Reset Button
Look for a tiny hole or button on the unit. On most Setek models, it’s small and recessed, sometimes labeled “RESET.” You’ll need something thin — like a paperclip or pin.

Press and Hold
Stick your paperclip in and hold the button for about 10–15 seconds. Watch the lights — usually they’ll flash rapidly or go off and back on. That’s your cue it’s actually resetting.

Release the Button
Let go after the lights start doing their thing. The extender will now reboot. Give it a minute or two — don’t panic if the lights are weird for a bit, that’s normal.

Reconfigure Your Extender
Once it’s back up, it’s basically like brand new. You’ll need to reconnect it to your WiFi network. Usually, you can do this via the web interface or Setek’s app. Enter your WiFi credentials, pick a network name (or keep the old one), and boom — it should connect.

Test the Connection

Connect with the network again with your phone or laptop and walk around your house. Check that the extended network is showing up and the signal is solid. In case of flaky signals, you might need to move the extender closer to the router.

How to Reconfigure After Resetting the Extender?

1. Plug it in and get close
Don’t try to configure this thing from across the house. Sit near the extender, plug it in, wait for the lights to stop blinking like a strobe. Most extenders need a solid connection to start the setup.

2. Connect to it directly
Open your laptop or phone and look for the extender’s network. Usually it’s something generic like “EXTENDER_SETUP.” Don’t bother trying your old Wi-Fi yet — the extender doesn’t remember it anymore.

3. Log in to the setup page
Pull up a browser and type the IP address or URL the manual says. Usually, it’s something like 192.168.10.1. If you forgot the credentials, they’re usually on the sticker on the device.

4. Scan for your main Wi-Fi
The extender should show you a list of nearby networks. Find your home Wi-Fi, click it, and type your password. Watch out for typos here — I’ve lost more time than I care to admit just because of one wrong character.

5. Name your extended network
You can usually keep the same name with a _EXT on the end, or pick a new one. Doesn’t really matter, just something you’ll recognize.

6. Save and reboot
Hit save, let the extender restart. Wait for all the lights to stabilize. It might take a few minutes, don’t panic.

7. Test it
Connect your device to the new extender network. Walk around your house. If you lose signal, move the extender closer to your main router. Placement matters more than people admit.

8. Optional: Advanced tweaks
If you’re picky, you can log back in and adjust channels, security settings, etc. But honestly, for 90% of setups, the default works fine.

Conclusion

As you can read above how to reset the Setek WiFi extender, what would happen if you do it. We have also given a guide for the other troubleshooting tips to avoid the resetting process.

But remember you have to reconfigure the device after your reset it once. To reconfigure you need to connect your PC with the Setek extender network. Then, go into the web browser and search for the 192.168.10.1 Ip address which is default assigned with the device. An interface will come on the screen and here you have to the enter the default admin credentials: the password will be “admin”. Access the interface and then manage the settings.